Scotts Spreader Settings Chart

February 24, 2024 Post a Comment

Scotts spreader settings chart

Calibrating Your Spreader

<ol class="X5LH0c"><li class="TrT0Xe">Divide 100 by the square foot the bag of fertilizer covers.</li><li class="TrT0Xe">Multiply the weight of the bag by this number.</li><li class="TrT0Xe">The answer is the amount of fertilizer needed to cover 100 sq. ft.</li><li class="TrT0Xe">Place this amount in the spreader.</li><li class="TrT0Xe">Mark off a 10 ft. x 10 ft. area.</li><li class="TrT0Xe">Apply using the suggested setting.</li></ol>

What do the numbers mean on my Scotts spreader?

The numbers stand for an application rate. A bag of commercial fertilizer will usually have numbers for where to set either broadcast or drop spreaders to get the recommended amount of fertilizer laid down.

How do I set my Scotts spreader?

Review any special application information in the apply section and identify the correct spreader

What setting should my spreader be on for seeding?

If your spreader's arc measures 12 feet across to its outermost points, the effective coverage is 9 feet wide. Passes across the lawn should be 9 feet apart. For best coverage, set the spreader at 50 percent, and then spread your seed two ways in a crosshatch pattern.

What setting should I put my Scotts spreader grass seed on?

For example, according to Scotts, the Scotts broadcast spreader settings for ryegrass seed should be set at setting 15 for new lawns and setting 5 for reseeding. Fertilizers will require a different setting as well.

What are the numbers on a fertilizer spreader?

All fertilizer labels have three bold numbers. The first number is the amount of nitrogen (N), the second number is the amount of phosphate (P2O5) and the third number is the amount of potash (K2O). These three numbers represent the primary nutrients (nitrogen(N) - phosphorus(P) - potassium(K)).

What are the numbers on Scotts Turf Builder?

A: Thank you for your question regarding Scotts Turf Builder Lawn Fertilizer. Those numbers are the NPK. Which is the amount of Nitrogen, Phosphorous, and Potassium in the product. The NPk for this product is as follows: Nitrogen-32, Phosphorous-0, Potassium-4.

What do lawn spreader settings mean?

A spreader setting is the rate in which you apply product to your lawn. Each Jonathan Green product has recommended rates of application and coverage based on bag size. The application rate is defined as the amount of material applied per unit area of land.

Are Scotts spreader settings lbs per 1000 sq ft?

The fertilizer bag states that I should apply 40 lbs. per 5000 sq. ft. or 8 lbs per 1000 sq ft.

How do you fix stripes on fertilizer?

As light green stripes are usually the result of missed gaps in your application, it makes sense that you can get rid of them by filling in those gaps. The best remedy is to apply a small amount of fertilizer in these specific areas. Using a drop spreader will be preferable in this instance.

How do you use the Scotts Edgeguard spreader?

How to use. Fill hopper with Scotts® lawn fertilizer or grass seed. Turn orange rate dial to the desired "Broadcast/Rotary Spreader" setting listed on the back of each Scotts® product. To apply product begin walking, then squeeze and hold trigger.

What setting should I use on Scotts spreader for lime?

Spreader	Setting
Central Quality (Drop) 175, 185, 205	12
Scotts (Drop)	11.5
Scotts (Broadcast)	J
Earthway EV-N-SPRED	21

What setting should I use on my Scotts spreader for starter fertilizer?

Spreader Not Listed - Setting Tip: Set spreader at 1/4 to 1/3 of the dial as a starting point.

How often should grass seed be watered?

Twice daily watering is essential until the new grass is up, then after one more week, reduce to once per day. Adjust this pattern according to season and temperature demands.

How much seed do you need to overseed?

If most of your lawn already has thick grass growth, overseeding will be a general maintenance task. In this case, you should use two to four pounds of seed for every 1,000 square feet of lawn. However, if your lawn has exposed areas of soil, apply four to eight pounds of seed per every 1,000 square feet.

What comes first fertilizer or grass seed?

Do I apply the fertilizer before seeding or after? Apply the fertilizer before seeding. When is the best time to plant a new lawn? Spring and fall are the best times to plant a new lawn.

Should I seed and fertilize at the same time?

Applying fertilizer at the same time you seed your lawn is not a recommended idea. Many experts will tell you that doing so you could risk to destroy a large part of your lawn where the soil was heavily fertilized.

Should you overseed or fertilize first?

Stop fertilizing for at least a month before overseeding. The fertilizer makes your grass grow faster, which makes it harder for the new seeds to take hold.

When should I apply 10 10 10 fertilizer to my lawn?

For 10 10 10 fertilizer, it is best to apply it in the early spring when plants are just beginning to start their most active growth phase. You can continue to apply a small amount of fertilizer during the dormant months of late fall and winter, or you can stop fertilizing for these months.

How do you calculate fertilizer?

Soil test recommendations are given in lb/ac or kg/ha of nutrients. To determine the fertilizer rate for a particular nutrient, multiply the rate of the desired nutrient by 100 and divide by the percentage of the nutrient in the fertilizer.