Manual Propress Tool

October 26, 2023 Post a Comment

Manual propress tool

IWISS develops a manual pressing tool work with the ProPress system for those who don't have too much work with copper tubings and want to save the budget.

Is ProPress better than solder?

Unlike soldering, ProPress systems do not need an open flame to be completed. This creates a safer work environment and by not requiring a hot work permit, saves time. Another advantage over soldering, ProPress fittings can be installed without having to drain and dry the system beforehand.

What is the life expectancy of ProPress fittings?

All depends on the water. Water treatment is a good plan regardless. It should be more than 25 years.

Are ProPress fittings expensive?

2. Basic ProPress machines will cost upwards of one thousand dollars, and bigger or more advanced units will cost much more. 3. The fittings are much more expensive than comparable sweat fittings.

Can you ProPress over a solder joint?

Essentially the distance is a multiple of the size of the tube diameter. Can you solder next to ProPress fittings? Yes. When soldering next to ProPress fittings, the installer must remain at least three tube diameters away from the connection to prevent damage to the sealing element.

Can you ProPress steam?

ProPress and ProPress XL (EPDM) is approved for use in Low Pressure Steam Applications, max 15 psig / max 248 deg F. MegaPress (EPDM) is approved for use in Low Pressure Steam Applications, max 15 psig / max 248 deg F.

Do ProPress fittings leak?

In general, Viega Propress fittings only leak due to one of three reasons; the fitting was never pressed, the copper tubing was not properly inserted or the pressing jaws were not properly aligned. If the fitting was never pressed, confirm that the tubing is properly installed and proceed with pressing.

Are ProPress fittings permanent?

connection during pressure testing when water flows past the sealing element. ProPress tool is used to press the fitting, making a permanent leak-proof connection.

Can ProPress go underground?

It's one of the most common questions we get: can MegaPress, ProPress and other fittings be used underground? The answer is yes.

What is the green dot on a ProPress fitting?

A green dot on a Viega ProPress, MegaPress fitting indicates Smart Connect technology with an EPDM sealing element. A yellow dot on a Viega MegaPressG fitting indicates Smart Connect technology with an HNBR sealing element.

Can you use ProPress on copper?

ProPress® and ProPress XL (Copper) are safe, reliable and economical copper pipe installation systems that use modern cold press connection technology. Viega® ProPress fittings are for use with type K, L and M hard copper tubing from ½" to 4" and soft copper tubing in ½" to 1¼" diameters.

How far apart do ProPress fittings need to be?

Tubing Diameter	Minimum Distance (inches)	Minimum Distance (mm)
2 in	3/4 in	20 mm
2-1/2 in	5/8 in	15 mm
3 in	5/8 in	15 mm
4 in	5/8 in	15 mm

How many PSI can a ProPress fitting hold?

Engineered for a variety of gas applications, including natural gas, LP gas and fuel oil, Viega ProPressG has been tested to withstand a maximum pressure of 125 psi and an ambient temperature range of -40 degrees F to 180 degrees F.

What are ProPress O rings made of?

EPDM is by far the most widely used material for O-rings in plumbing fittings around the world. Viega uses EPDM for all their ProPress Fittings, (used in Europe for over 30 years where high levels of chloramines are common.)

Can you use ProPress on a boiler?

Devix Heating and Cooling uses ProPress for nearly all its water heater and boiler repairs and installations.

Can Propress used in natural gas?

Suited for natural gas, LP gas, and fuel oil installations, ProPress G uses Â½-2 in. copper fittings and hydraulic pressing tools, which are fitted with interchangeable jaws in 9 sizes.

Can Propress be used on gas?

Pro-press has copper GAS fittings. These contain Yellow O-rings for use with gas and oil!

Can Propress be used on refrigeration?

Machining single ring propress for refrigeration lines is the other way to manufacture the Miracle single ring. You can also call it turning single ring propress for refrigeration lines.

Can Propress be used for propane?

Propress G press fittings are manufactured with a high quality HNBR sealing element installed at the factory. This sealing element is used mainly for applications of natural, propane, mixed, and manufactured gases, and can be used in fuel oil systems.

Can you use ProPress on PEX?

ProPress copper to PEX fittings are needed when installers are adding new supply lines to a home or business. Traditionally, making these connections involves the use of sweat adapters.